1. Home
  2. Categories
  3. 3D Models
  4. 3D Printers
  5. Accessories

Accessories

Photo Title
Description
P3Steel SumPanel mount

After the latest upgrades to my TronXY X5S (https://burningbecks.wordpress.com/tag/x5s/) the bits box was full of RepRap components.
The main reason for starting building with the P3Steel frame was to put some parts, still too good to be just thrown …

P3Steel Version 2.5 RAMPS spacer / offset mount

As my "v2.5" frame (with motor mounts on the side panels) could not be fitted with toolson's orignal "RAMPS offset mount" I made this in Open SCAD.

Materials needed:
4x M3 nut
4x M3 nyloc nut
6x M3x6
2x M3x20

End cap for (Reverse-)Bowden-Tubes, customizable

Made this to improve filament protection from moisture. (It should tighten against unwanted airflow into your drybox.)
There is still a meter (or so) unrolled from the spool between my drybox (https://www.youmagine.com/designs/slim-anti-tangle-dual-s…

Dual PSU holder for 2020 profiles, made for TronXY X5S

Holds two 360W power supplies at the back of the frame.
To install the "Tronxy X5S Single z motor mod by spegelius" (https://www.thingiverse.com/thing:3612257) I needed to fix those power supplies somewhere to the frame.
So I made this.

It holds the st…

"Mk2" TronXY X5S X-Carriage for MGN12 linear rail

Metal BMG extruder, Hangtight part cooler, threaded E3Dv6 Hot End, matches my Y-Gantry.

This replaces my "TronXY X5S X-Carriage for MGN12 linear rail" (which uses an E3Dv5 / "China J-head" hotend, a Prusa-style, ungeared extruder and a Petsfang part …

Filament guide for Sanjiu / SANBrother Metal BMG extruder

UPDATE:
The "v4" (blue part in the pictures) was already much tighter, than the (black) stock piece. But it was still not tight enough to print flexibles properly.
The "v5" (depicted in copper) should tackle that now.

My specimen was printed with a 0.3…

Filament feed-through for dual pneumatic fitting

Flanged, to be mounted to wooden panels.

Made this to connect the reverse Bowden tube from my old drybox (https://burningbecks.wordpress.com/2018/06/30/filament-drybox-from-paint-bucket/) to my housing for the X5S. And then guide the filament from th…

Gypsum board to 2020 adaptor

Used this to mount a bottom panel / low flammability floor panel to my X5S.
Makes carrying it a lot easier.

Nozzle marker / sorter / holder for M6-threaded non-Volcano nozzles

As I like to keep my nozzles sorted by source, I needed something flexible to adapt to what was in those individual packages.

If you want to compile your own, your need http://en.wikipedia.org/wiki/ISO_metric_screw_thread => threads.scad

Pre-compiled …

Fix for snapped cable chain carriers

Spare part for "TronXY X5S X-Carriage for MGN12 linear rail".

If you did put the M3 nuts into the "nut trap for future upgrades" parts, you can use this in case your "Vertical Cable Chain" counterparts snaps off...

You'll need two M3 bolts, ~10mm (whe…

Reinforced motor mounts with bushing for shaft

STLs in ZIP archive.

These motor mounts adress a couple of issues I had with the "Tronxy x5s reinforced left motor mount by xxdanmurphyxx" and my own counterpart, still contained in https://libre3d.com/category/603/Accessories/listings/1228/TronXY-X5…

Slim Anti-Tangle Spool Holder - fits two #MasterSpool into one IKEA 365+ (10.6l)

Why I did this:

  • Dasfilament.de overfill their #MasterSpool refills to 850g (they still deliver the best refills I know, though).
  • A freshly refilled spool thus is in constant danger of filament jumping over the edges.
  • Both Mark Rehorst and Graha…

TronXY X5S X-Carriage for MGN12 linear rail

OLD VERSION - UPDATE AT:
https://libre3d.com/category/603/Accessories/listings/1264/Mk2-TronXY-X5S-X-Carriage-for-MGN12-linear-rail.html

This is meant to complement my Y-Gantry (and finally align the belts again):
https://libre3d.com/category/603/Acces…

Split HTD3 pulley for TronXY X5S Z axis sync

Prevents heatbed sagging while Z-motors are unpowered.
These pulleys keep the unpowered Z-motors of my TronXY X5S in sync, so I don't have to constantly re-level the heated bed. RPP3-belts (fitting the HTD3-pulleys) were from the bits box - when sour…

TronXY X5S adaption of Prusa i3 Mk3 Extruder (R3/B7) & E3Dv5 / XCR-BP6

Description is at: https://burningbecks.wordpress.com/2018/11/17/the-prusaic-extruder-x5s-goes-direct/

Note that the work this part is based on it NOT licensed permissively, but "Copyleft"!

Converted my TronXY X5S ( https://burningbecks.wordpress.co…

Adaptor from TronXY metal plate to Vertical Cable Chain

This will adapt https://www.thingiverse.com/thing:3071908 (Tronxy X5S Top Mount Cable Chain Remix by Vetterick) to the stock metal plate of the carriage.

TronXY X5S CoreXY Y-Gantry Set

Documentation of build at: https://burningbecks.wordpress.com/2018/12/25/new-y-gantry-stacking-the-pulleys-again/

As Libre3D.com's auto-compiler collides with uploading derived STLs parallel to the SCAD file that generates them, you man want to look …

TronXY X5S reinforced motor mount without raise

Corresponding blog post: https://burningbecks.wordpress.com/2018/12/25/new-y-gantry-stacking-the-pulleys-again/

xxdanmurphyxx designed a reinforced (left) NEMA 17 motor mount and published it on Thingiverse (as CC-BY).
As the motor shaft position is i…

TronXY X5S Y-Gantry for MGN12 linear rails on 2020 extrusion (customizable)

Blog post about it: https://burningbecks.wordpress.com/2018/12/24/open-hardware-y-gantry-plates-x5s-stls-finally-hosted/

As Libre3D.com's auto-compiler collides with uploading derived STLs parallel to the SCAD file that generates them, you man want t…

Tronxy X5S Melzi2.0v5 PCB bottom cooler

See my blog post for details: https://burningbecks.wordpress.com/2018/03/24/tronxy-x5s-heatbed-and-movement/

On Tinkercad: https://www.tinkercad.com/things/gUTlx5egCtZ-tronxy-x5s-melzi20v5-bottom-cooler

TronXY X5S HBP drag chain mount

Adaptor, based on the "tl-ban-2" file supplied with the printer.

Allows mounting of the drag chain of the TronXY X5S closer to the heated bed / farther away from the frame, to enlargen the bend radius of the cables. See blog post for details:
ht…

Phoenix Unlimbited 3D printable mechanical prosthetic hand from E-Nable

  These are the parts for the phoenix unlimbited 3D printable mechanical prosthetic hand from E-Nable 

Test

This is a test file

Drill Dust collector

Drill Dust collector 3d print.

endstop long holder

a long endstop holder

Alexa Rocket Base

Simple rocket base for Alexa. Originally from here: https://www.thingiverse.com/thing:1785459

NEMA17 Spacer Plate

This part is used to space the E3D Titan Extruder body away from the face of a NEMA17 motor.

Earring holder

Its a tree shape earring holder, which consists of just 2 prints , not more than an hour.
Simple and effective design.

CustomSolid INTERLOCKING M3D Micro Spool Holder Bushings

I Didn't like/Couldn't Use ANY of the spool holder bushings that I found already designed for the M3D Spools successfully...
(They would keep walking out of the spool and then my spool would drop onto the spindle of my filament holder and everything …

infnty

infnty emblem to be used for cool stuff. I am not affiliated with nor have I ever been affiliated with infnty. Logo is their property. This is just a cool emblem I decided to make for fun

Bowden support without Hotend modification

Bowden support for Argento hotend.

Android Phone Arm for Replicator 1

An instructiable opened my eyes to the fact that an old Android phone can be used as a webcam (resource link #1) but instead of an IP camera I used the uStream app to make my 3D printer live broadcast (resource link #2).   These models I don'…