Sort By:   GridListGallery

 3D Printers

Split HTD3 pulley for TronXY X5S Z axis sync
 : 2 |   : 0

Prevents heatbed sagging while Z-motors are unpowered. These pulleys keep the unpowered Z-motors of my TronXY X5S in sync, so I don't have to constantly re-level the heated bed. RPP3-belts (fitting the HTD3-pulleys) were from the bits box - when sourcing new parts GT2 pulleys with 60 teeth and a...

Bigtreetech SKR mounting bracket for Duplicator i3 / Maker Select / etc
 : 1 |   : 0

A simple mounting bracket for the new Bigtreetech SKR 32-bit control board as a replacement for the stock Melzi board in a Wanhao Duplicator i3 type printer.  Mounting holes are 2.7mm ID and should easily self-tap with M3 screws. If you print this in PLA and find that the mounting bosses...

 Di3 or Maker Select mounting bracket for RAMPS and/or Re-ARM with mosfets
 : 1 |   : 0

This is a mounting bracket for the Wanhao Duplicator i3 or Maker Select to allow replacement of the original melzi board with a RAMPS, with either the Mega2560 8 bit processor or with the Re-ARM 32-bit processor.  There is also accomodation for two kinds of bed mosfets, and a version with...

TronXY X5S CoreXY Y-Gantry Set [STLs only]
 : 9 |   : 0

Documentation of build at: https://burningbecks.wordpress.com/2018/12/25/new-y-gantry-stacking-the-pulleys-again/ DUE TO TECHNICAL DIFFICULTIES WITH UPLOADING ONLY STLS HERE - CODE AT: http://libre3d.com/category/603/Accessories/listings/1178/TronXY-X5S-CoreXY-Y-Gantry-Set-[OpenSCAD-only].html ...

 TronXY X5S adaption of Prusa i3 Mk3 Extruder (R3/B7) & E3Dv5 / XCR-BP6
 : 3 |   : 0

Description is at: https://burningbecks.wordpress.com/2018/11/17/the-prusaic-extruder-x5s-goes-direct/ Note that the work this part is based on it NOT licensed permissively, but "Copyleft"! Converted my TronXY X5S ( https://burningbecks.wordpress.com/tag/x5s/ ) with this and my old E3Dv5 to...

TronXY X5S CoreXY Y-Gantry Set [OpenSCAD only]
 : 9 |   : 0

Documentation of build at: https://burningbecks.wordpress.com/2018/12/25/new-y-gantry-stacking-the-pulleys-again/ DUE TO TECHNICAL DIFFICULTIES WITH UPLOADING ONLY CODE HERE - STLS AT: http://libre3d.com/category/603/Accessories/listings/1181/TronXY-X5S-CoreXY-Y-Gantry-Set-[STLs-only].html ...

TronXY X5S reinforced motor mount without raise
 : 1 |   : 0

Corresponding blog post: https://burningbecks.wordpress.com/2018/12/25/new-y-gantry-stacking-the-pulleys-again/ xxdanmurphyxx designed a reinforced (left) NEMA 17 motor mount and published it on Thingiverse (as CC-BY). As the motor shaft position is important for CoreXY mechanics and he didn't...

CoreXY test piece for speed, jerk, acceleration
 : 2 |   : 0

Test piece for speed, jerk, acceleration as well as ringing, vibration, vertical banding and other artefacts. Ran some tests on my CoreXY printer with two " Test part to look at X and Y damping and resonance by MiseryBot", but realized, that it was too small. This part has the 45° and...

TronXY X5S Y-Gantry for MGN12 linear rails on 2020 extrusion (customizable)
 : 5 |   : 0

Blog post about it: https://burningbecks.wordpress.com/2018/12/24/open-hardware-y-gantry-plates-x5s-stls-finally-hosted/ If you can't read the description here, look at YouMagine: https://www.youmagine.com/designs/tronxy-x5s-y-gantry-plate To re-arm my TronXY X5S, I am currently rethinking...

Tronxy X5S Melzi2.0v5 PCB bottom cooler
 : 2 |   : 0

See my blog post for details: https://burningbecks.wordpress.com/2018/03/24/tronxy-x5s-heatbed-and-movement/ On Tinkercad: https://www.tinkercad.com/things/gUTlx5egCtZ-tronxy-x5s-melzi20v5-bottom-cooler

TronXY X5S HBP drag chain mount
 : 1 |   : 0

Adaptor, based on the "tl-ban-2" file supplied with the printer. Allows mounting of the drag chain of the TronXY X5S closer to the heated bed / farther away from the frame, to enlargen the bend radius of the cables. See blog post for details: ...

Test
 : 1 |   : 0

This is a test file

Cubicle Wall Hanging Shelf Modified
 : 1 |   : 0

This is a modified version of the http://libre3d.com/category/511/Frames/listings/1077/Cubicle-Wall-Shelf.html item. The other one didn't work out the way I wanted it to, so I modified the SCAD to make it fit my cubicle wall as well as making either side be able to fit. So it can hold the...

Cubicle Wall Shelf
 : 1 |   : 0

https://www.thingiverse.com/thing:2439255 Copied from Modem7, uploaded here to auto convert to STL to be able to print.

glass holder
 : 1 |   : 0

https://www.thingiverse.com/thing:1718711

Alexa Rocket Base
 : 1 |   : 0

Simple rocket base for Alexa. Originally from here: https://www.thingiverse.com/thing:1785459

NEMA17 Spacer Plate
 : 1 |   : 0

This part is used to space the E3D Titan Extruder body away from the face of a NEMA17 motor.

Tree
 : 1 |   : 0

customised

Earring holder
 : 2 |   : 0

Its a tree shape earring holder, which consists of just 2 prints , not more than an hour. Simple and effective design.